Forgotten your password?

Customer Login:

Uk's Leading Retailer for Quadcopters, DJI Drones, FPV Equipment and CAA Approved PfCO Drone Training.

​​​​​​​To Speak to One of Our Team
​​​​​​​01257 443370
Click LIKE to the left and we will keep you update with offers and news. If you would like to visit our Facebook page, click now.


Does it support multicopters with only 3 propellers included?

No, it doesn’t.

Does it support Spectrum transmitters and receivers?

Yes, it does.

Do I need use BEC seperated to power the MC?

No need, VU already includes BEC function.

Can I use Y wire to connect two motors?

In principle, one MC port connect to one ESC and one motor.

What can I do, my aircraft always drifts forward?

Never move aircraft within 5s after power it on. No trim in your transmitter.

Low-Voltage Warning is available in manual mode or not?

Yes,Low-Voltage Warning is available in manual mode.

Arming makes motors tune too fast or too slow, what can I do?

Please change Motor Idle Speed through assistant software.

Please explain why computer doesn’t recognize USB device?

Make sure driver has been installed sucessfully, PMU should be connected to LED port of MC, not Ext port.

Which OSD can support NAZA?

NAZA has no OSD function, 3rd part OSD product can be used.


Can NAZA-M be used on helicopters?

No,It can’t be used on helicopter.

Why did I fly the NAZA-M not stable in the low-temperature environment?

Place your aircraft outside for minutes firstly.

What’s the usage of NAZA-M EXT port?

Used for GPS Module.

Does NAZA-M support PPM receiver?

Yes, it does.

Some aircrafts with Naza installed drift a lot, some very stable. How is that?

You can not have position lock without Naza GPS module. The flight performance will affected a lot by the environment,such as windy condition, mechanically setup, center of gravity, etc.


After register finished through assistant software, why I still can’t log in?

Please log in your emial box, and click the link to activate the register firstly, then you can enter the software with the email and password to log in.

What can I do when software and main controller can’t be connected?

The assistant driver has not been installed sucessfully. With MC powered firstly, USB cable connected, then install the driver.

How to deal with the configuration error?

Please calibrate your transmitter sticks and then restart MC.

No reaction from motors when do arming, what happened?

Please refer detailed instructions in the manual. Start software to check if the control stick on your transmitter can reach the full range, directions are correct or not. Please unplug USB when you do the testing.

Flight Parameters recommended for Flame Wheel F550?

Default parameters are 100% normally, but it can be adjusted according to actual flight conditions and different control feeling.

How to set up 3-switch for flight control mode?

Connect switch channel to U channel of MC, use Trim menu to adjust 2nd switch to Atti. Mode, use End Point to adjust 1st and 3rd switch for Manual mode and GPS mode.

How to set up Fail-Safe?

Make sure all channels of your transmitter include Fail-Safe, adjust any one of the 3 switch control modes to Fail Safe mode, then record the position value in Fail Safe of your Tx. After that, switch to other control mode and turn off the transmitter, assistant software show it jumps into Fail Safe mode and meantime LED shows blue ligh, setup is done.

How to match propellers and motors?

Very important to match Props and motors to get good flight performance. 900KV motor matching 8-10 inches Props are recommended.

What happended when LED flash Red light quickly?

Connect MC with software to check what problem is and then find out a corresponding solutions.

Where should the main controller be placed?

MC has to be installed close to C.G. No need any damping, just use 3M double-side sticker.

What mode should be used in Transmitter?

Set your model type as Airplane.

Does the software support Vista OS?

Yes, it does.

The height can’t be locked, why?

Adjust vertical gain, use defaul throttle curve and 50% throttle for hovering.
Looking to Purchase the
DJI Naza Flight Controller then are UK Official DJI Dealers For DJI Innovations and DJI Hobby