close
Forgotten your password?

Customer Login:


Uk's Leading Retailer for Quadcopters, DJI Drones, FPV Equipment and CAA Approved PfCO Drone Training.


​​​​​​​To Speak to One of Our Team
​​​​​​​01257 443370
£259.00
Earn 259 points with this purchase.
  • Description
  • Reviews

ImmersionRC Vortex 150 ARTF EU Spec

* The EU Version is identical to the International, and USA versions, with one exception. The firmware is region-locked to prevent transmission outside of the EU ISM band. All ImmersionRC/FatShark channels are still available, along with 6 of the 8 RaceBand channels. Power output is limited to 25mW also to meet EU RTT&E Regulations.
Following on from the incredible success of the Vortex 285 and Vortex 250 Pro, the Vortex 150 Mini from ImmersionRc raises the bar and at the same time shrinks the size to make this the most compact agile mini racing drone available in a bnf configuration.

The essence of the Vortex family, ARF/RTF, fully integrated flight controller, OSD, and video transmitter.

Fusion2 + Tramp = Synergy

Vortex 150 Pro UK
 

The new ImmersionRC ‘Synergy’ flight controller integrates a full-graphic OSD and an onboard video transmitter based on the new Tramp HV design.
Twin F3 processors ensure an 8kHz loop time and full support of BetaFlight 3.x.
Factory calibrated power levels from 1mW ->, glitch-free channel changing, and a micro-power pit-mode ensure that the Vortex 150 will receive a warm welcome at any race event.

The Synergy weighs in at a mere 6.41g, vs. the Fusion Gen2’s 10g, the latter without a video transmitter!

Integrated Leading-edge 5.8GHz Video Tx

ImmersionRC Vortex PRO 150 Racing Drone - Quadcopters.co.uk

The fully integrated ‘Tramp’ video transmitter has all the bells and whistles. Support for all standard FPV channels.

Dynamic Power Control, introduced with the Vortex 250 Pro, is taken to a new level, pre-take-off power level may be dropped to sub-1mW while waiting on the starting grid, saving precious battery power, and keeping temperatures low.

After a crash landing the power level is dropped to a minimum to preserve battery life during the search and to help with localization using a directional antenna.

 

Integrated Touch’n’Race

Vortex Wand Touch and Race

A TNR (NFC) antenna integrated into the side of the quad provides full support for the ImmersionRC Personal and Race Director’s wand. The latter enables additional channels for events with special spectrum use permissions.

Setting your video transmitter frequency and power without touching the quad, greatly simplifying casual and race channel setup. No fiddly dip switches, no push-buttons and key-press sequences to remember and no guesswork.


PRODUCT SPECIFICATIONS
Weight: < 250 grams with 500mAh 4s pack
Power Requirements: 3s-4s LiPo, 4s 750mAh >45C recommended
ESCs: Full Custom, 16A cont. 20A peak, rotorSENSE, OneShot125, OneShot42
Motors: Custom V-Spec 1306-3200kV
Props: RaceKraft 3″ Tri-Blades
Flight Camera: FatShark CCD (HS1177 Sensor & Chipset)
Receiver Compatibility: CPPM, S-Bus, Spektrum™, XBus, SumH, SumD (no external adapters required) (Auto-Sense!)
Flight Time: Highly dependent upon battery, and flying style, 3-4 mins typical
Note: Compatible receiver and display device required for initial setup and use, not included.

 

Included in the box

  • 1x Vortex 150 Mini Race Quad, Fully assembled and flight-tested
  • 2x ImmersionRC Branded battery straps (Installed)
  • 1x SpiroNET Omni 5.8GHz antenna (Stubby, v2)
  • 1x PPM Interface Cable
  • 1x Spektrum(tm) Interface Cable
  • 1x SBus Interface Cable
  • 8x RaceKraft 3" Tri-Blade Props

Customer Reviews

Write an online review and share your thoughts with other shoppers!

Be the first to review this product