Hobbywing X-Rotor F4 G3 Combo Featuring a new F4 G2 Flight controller and a 60A 4 in 1 Esc.
New third generation of the popular hobby wing stack, now with a updated 60a esc.
A very popular combo stack with the FPV Drone racers around the world as its a proven reliable system that offers ease of set up with performance thats demanded by the fastest and most aggressive pilots.
Hobbywing are well known for there quality and reliability in there flight controllers and escs especially in there stacks. Standard 30x30mm Mounting Holes.
XRotor Micro Flight Controller F4 G3
Super hardware, fast running speed integrates with STM32F405 MCU which features
powerful computing capacity & super operating speed and high sensitivity ICM20602 6
axis motion sensor. It can run PID cyclic frequency and gyro refresh frequency at 32KHz.
Integrated OSD chip can set OSD parameters on FMU parameter software and remote
controller. Convenient and simple. Integrated OSD extended slot can record and save
more flight log which is convenient for user to adjust aircraft based on flight data.
Onboard 12V BEC
FMU integrates with 12V BEC circuit. It can supply super
power output for image transmission and 12V LED devices.
Onboard Pit Switch module
FMU integrates with Pit Switch module. After adjust it on FMU
parameter-adjusting software, directly use remote controller to
open or close VTx. Simple and convenient.
Perfectly support various machine firmware
Perfectly support BetaFlight,leanflight, Butterflight and inva. It is convenient to adjust
various parameters via corresponding parameter software. Make FMU suitable for
various FPV flight and competition.
Unique shock absorption structure
Unique soft layout connection mode ( integrate with Hobbywing stack
4 in 1 ESC will be better). Add shock absorption structure for installation hole
to reduce the external vibration impact. Make the flight stable and precise.
Perfectly integrated with Hobbywing’s ESC
Integrated with Hobbywing stack 4 in 1 ESC makes the wiring & installation easy and simple.
XRotor Micro 60A 4in1 BLHeli32 6S
With a similar size of a FC, the 4IN1 ESC includes 4 high performance 60A BLHeli_32 DShot1200 ESCs,
a 5V BEC which can provide power for devices (i.e. FC), and a voltmeter which allows FC to monitor the
amp & volt in real time. Two ways for connecting the ESC to a FC: 1) connecting via soft cables, 2)
soldering via solder tabs are provided for selection. And the shock-absorbing design of mounting holes
effectively reduces the external vibration’s impact on high-sensitivity components and provides great
shock-absorbing protection to upper devices (i.e. FC). This ESC is designed for FPV racing.
High Quality Components
High Quality Hardware Large-size MOSFETs imported from Japan make the 4IN1 ESC have greater voltage/current endurance
than the last generation (at high voltages). The use of high performance 32-bit microprocessors with
operating frequency of up to 48MHz, 3-in-1 drive ICs, imported high quality ceramic capacitors,
3-ounce copper, 6 layers of PCBs guarantees less heat, higher efficiency and rapider response.
Innovative Shock-absorbing Structure
The Innovative connecting method via a soft cable (*it works better when pairing with
the XRotor Micro-F4-G3 Flight Control) combined with the shock-absorbing design of mounting
holes effectively reduces the impact on high-sensitivity ESC components from outside
shock and provides great shock-absorbing protection to upper devices (i.e. FC).
BLHeli-32 Firmware Ready
The ESC flashed with the 3rd-generation BLHeli-32 firmware has great
performance & rich functions and supports adjusting parameters or upgrading
firmware via different ways (i.e. via throttle signal wire with using other
development board or a FC flashed with the Cleanfight/Betaflight firmware).
DShot1200 Ready ! Besides the regular PWM mode, Oneshot125/Oneshot42/Multishot
modes, DShot150/300/600 modes, the latest DShot1200 mode is
also supported. In DShot1200 mode, the ESC has great
anti-interference performance and rapid response.