iFlight SucceX-D F7 Stack (F7+60A ESC) for DJI Air Unit 2-6s

333 Reward Points
SKU:
Brand: iFlight

Quantity

ADD TO WISHLIST
Found it cheaper? Click here

Sorry this item is out of stock, please complete in the form below to be notified when stock is available.

QuadCopters Price Match

Where you've seen it cheaper (UK Stores Only)

The SucceX-D was designed and built by iFlight to support the all new DJI FPV Digital system and works flawlessly.
60A Esc with F7 Processing Power perfect for high performance 2s-6s racing or freestyle drones. 
A simple plug and play system which literally just plugs into the DJI Air Unit. This is also USB C so you can use the same cable for both your DJI air unit and the FC.
This kit includes the Flight controller and the 4 in 1 60A esc. (DJI Air unit not included and is sold seperate)
This is the highest rated stack from iflight which is designed to be paired with the DJI System and is rated for 2s - 6s set ups. Even the most power hungry motors and props won't be a problem for this combo.

PRODUCT DESCRIPTION

The SucceX-D F7 is designed to work seamlessly with DJI’s new HD FPV system. To make things as simple as possible, we have included a connector specifically for the DJI air unit, so installation should be a breeze. In addition, we add the popular and reliable USB Type-C instead of Micro USB which makes the connection easily.

Features

• Universal USB Type C connector instead of micro USB

• Plug-and-Play. No need to solder tiny wires.)

• Supports BLHeli pass-through for easy ESC upgrade and configuration.

• Designed to support DJI Digital FPV.

SucceX-D F7 TwinG  SPECS:

- MCU:216MHz STM32F722RET6

- Gyro: 2x ICM20689

- Baro:YES

- Betaflight OSD:YES

- Blackbox: 32MB

- 5 x Uarts

- 8 x Motor outputs

- 8 pin 4in1 ESC port

- 4-pin VTX connector

- Betaflight Firmware:betaflight_4.0.5_STM32F7X2.hex

- CLI config:IFLIGHTF7_TWIN_G.config

Physical 

- Mounting hole:30.5*30.5mm,φ4mm with Grommets φ3mm 

- Size:36*36mm 

- Weight:7.5g 

SucceX 60A BLHeli_32 4-in-1 ESC

Features:

- 8 layers single-board stacking PCB board;

- 4oz 1.6mm thick power board(0.9mm copper ratio),better operating load capacity;

- 32bit FO51K86 MCU,48mHz running speed;

- TDK MLCC Low ESR ceramic capacitors;

- Top grade metal MOSFET;

- Rational layout, countersunk holes on extended motor soldering pad enable each layer board can be powered.

Specification:

- Dimension:43x39mm

- Mounting Holes: 30.5*30.5mm/Φ4mm

- Weight: 13.4g

- Supports 2-6S lipo input

- STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware

- Current sensor: Yes

- BEC: No

- Supports: DShot DShot150/300/600/1200/MultiShot/ OneShot etc.

- Target: iFlight-BL32-4 in 1

DOWNLOADS:

Package included:

-SucceX-D F7 TwinG FC

-SucceX 60A BLHeli_32 4-in-1 ESC

Downloads:

Please verify the latest Update on Github:

Betaflight_4.1.0_STM32F7X2 for DJI Air Unit

Betaflight 10.6.0 configurator for DJI Air Unit

To restore hardware related parameters, please paste following config into your CLI after every betaflight reflash:

IFLIGHTF7_TWIN_G.config

dont forget to save with the "save" CLI command.


Wiring Diagram *png:

SucceX-D F7 Manual Instruction

OK

The item has been added to your basket

Continue Shopping
Proceed To Checkout